fishing rod holder rack 5x cornner unit
-
- Rank: Flathead
- Joined: Tue Jun 25, 2013 12:48 pm
- Likes received: 2 times
fishing rod holder rack 5x cornner unit
Hi fishos,
I have recently purchased a Savage Dolphin and I am looking at fitting a corner type snapper rack which fits into 2x flush rod holders at a certain centre distance (420mm from memory)
Has anyone had any experience with this type of rod holder and if so are they ok to fit?
Do I have to reinforce the fibreglass before fitting the flush mount rod holders?
Any info would be good. i am a tradesman and tool savvy. cheers
I have recently purchased a Savage Dolphin and I am looking at fitting a corner type snapper rack which fits into 2x flush rod holders at a certain centre distance (420mm from memory)
Has anyone had any experience with this type of rod holder and if so are they ok to fit?
Do I have to reinforce the fibreglass before fitting the flush mount rod holders?
Any info would be good. i am a tradesman and tool savvy. cheers
-
- Rank: Kingfish
- Joined: Sun Nov 11, 2012 7:42 pm
- Has liked: 26 times
- Likes received: 58 times
Re: fishing rod holder rack 5x cornner unit
are you talking rod holder for rods yr not using ???
or rods under pressure ?
bm
or rods under pressure ?
bm
you gotta hav a crack even if yr just pissin in the wind
- adamk
- Rank: Premium Member
- Joined: Sat Feb 07, 2015 3:48 am
- Location: laverton
Re: fishing rod holder rack 5x cornner unit
pictures of where you are going to attach it ?
but if in doubt reinforce, that's the way i see it.
but if in doubt reinforce, that's the way i see it.
-
- Rank: Kingfish
- Joined: Thu Aug 08, 2013 5:08 pm
- Location: Bellarine peninsula
- Has liked: 333 times
- Likes received: 569 times
Re: fishing rod holder rack 5x cornner unit
Whatever you do don't put plastic flush rod holders they snap under pressure. Are you talking about the right angle 5way rod holders like this
- Attachments
-
- 14251977434991.jpg (80.99 KiB) Viewed 813 times
-
- Rank: Flathead
- Joined: Tue Jun 25, 2013 12:48 pm
- Likes received: 2 times
Re: fishing rod holder rack 5x cornner unit
Hi Guys, rod holders as pictured in the last post for fishing not transporting made of ss set at a right angle. I think the vertical s have a slight taper to lock into the flush mount rod holders.
-
- Rank: Kingfish
- Joined: Sun Nov 11, 2012 7:42 pm
- Has liked: 26 times
- Likes received: 58 times
Re: fishing rod holder rack 5x cornner unit
Then need supporting imo
Straight into fiberglass will end in tears.
Nude up can help you more..he has a great stainless steel set up....mounted on the flat plane off boat
Bm
Straight into fiberglass will end in tears.
Nude up can help you more..he has a great stainless steel set up....mounted on the flat plane off boat
Bm
you gotta hav a crack even if yr just pissin in the wind
- paulpaciocco
- Rank: Cephalopod
- Joined: Sun Nov 23, 2014 8:11 am
Re: fishing rod holder rack 5x cornner unit
Barra mick is spot on mate. I do glass boat repairs and I can assure you that straight into glass will certainly end in tears. Over time from constant use and weight shifting on/off, you will start to see spider cracks around your fixings. Best thing to do is reinforce, by glassing a piece of marine grade hardwood, cut to measure under your rails. Glass it on properly and then through bolt with stainless bolts/washers/nuts. PM me if you need any further help buddy
Sent from my iPhone using Tapatalk
Sent from my iPhone using Tapatalk
-
- Rank: Kingfish
- Joined: Thu Aug 08, 2013 5:08 pm
- Location: Bellarine peninsula
- Has liked: 333 times
- Likes received: 569 times
Re: fishing rod holder rack 5x cornner unit
I think the above rod holder the outboard fitting goes in on an angle the two vertical must just sit on top if they plugged in then you would struggle to get the outboard angle one in, I would ask the supplier how are they mounted . I had mine custom made to suit my boat by maquarries in Williamstown. But everybody is correct the upper deck of most boats is quite thin 5 to 8 mm constant pressure will cause the gel coat to crack and use bolts not screws to hold them screws always come loose.
-
- Rank: Flathead
- Joined: Tue Jun 25, 2013 12:48 pm
- Likes received: 2 times
Re: fishing rod holder rack 5x cornner unit
Cheers guys I will definately reinforce. I have the boat at home until next snapper season so I have time to do a quality job. the old boat will do me until May.
-
- Rank: Murray Cod
- Joined: Tue Apr 16, 2013 5:39 pm
- Has liked: 136 times
- Likes received: 324 times
Re: fishing rod holder rack 5x cornner unit
Got 8 a side on the old mans boat. Custom stainless that fits straight into 2 flush mount rod holder's, one at the back, one about 500mm up the side. No other reinforcements etc. Very little movement on other rods in the holder's.